Boral Shingle Repair Nationwide

Boral Shingle Repair: The Austin Owner’s Guide

We stock and install Boral-compatible shingle repair parts across Austin, with most individual shingle replacements running $225 – $475 installed depending on roof pitch, accessibility, and how many shingles the damage actually spread to. Boral’s stone-coated steel and tile profile shingles aren’t something any general roofer keeps on the truck, but we do, because we made a point of stocking for all seven manufacturers we install, Boral included. Most Austin homeowners find out they need Boral shingle repair after a hailstorm or a wind event, though sun degradation and impact from falling live oak branches account for plenty of our calls too. You’ll either spot a cracked or lifted shingle from the ground, or you’ll find granules and stone chips in your gutters after a storm. Either way, the fix is usually faster and cheaper than people expect, as long as you catch it before water gets under the roof deck.

Call (254) 540-7345

Which Boral Models This Applies To

Boral’s roofing lineup has shifted over the years, but the repair work we do in Austin mostly involves three lines: the stone-coated steel profiles (think Boral Steel, often sold under the Gerad or Inspire names depending on the era), the concrete tile profiles, and the older composite/slate-look shingles. The stone-coated steel panels interlock, which means one damaged panel sometimes means removing and replacing a section of a few, not just a single piece. The concrete tiles, by contrast, usually come out as single units. Here’s the compatibility gotcha: Boral changed the profile of their interlocking ridge caps about eight years back, so if you have one of the earlier installations, a modern ridge cap from Boral will not seat correctly on the old rake design. We keep both generations in our Austin stock because we’ve run into exactly that mismatch more than once. If you’re trying to identify what you have, look for a label on the underside of a lifted tile or check the original invoice for a series number. If neither is handy, our techs can match by profile measurement and fastener spacing, which we do for free as part of the repair estimate. Tilehurst Roofing Austin is an independent service provider; we install and repair Boral roofing, but we’re not a Boral company or affiliate.

Signs Your Boral Shingle Repair Is Failing

• Granules or stone chips collecting in the gutter. Boral’s stone coating takes a beating from Texas hail, and when the coating starts shedding, the steel or composite beneath is exposed to UV and moisture. Call us when you see this; waiting turns a $300 shingle repair into a $1,800 decking repair.
• Visible cracks or spider-webbing on the tile face. Austin’s freeze-thaw cycle, mild as it is, still stresses rigid tiles, especially where leaves hold moisture against the surface. A hairline crack today is a full split after the next hailstorm.
• Lifted or rattling shingles in high wind. Boral products are heavy and usually wind-rated up to 120 mph or more, but clips and fasteners can fatigue. If you hear tiles clacking during an Austin thunderstorm, a clip has failed, not the tile itself.
• Water staining on ceiling or attic sheathing in one isolated spot. Unlike asphalt shingle failures that spread due to mat saturation, Boral failures tend to be point-source. One cracked tile equals one wet spot. Find the crack, swap the tile, and the leak stops.
• Rust streaks on stone-coated steel panels. If you see orange streaking below a panel edge, the stone coating has been compromised and the steel substrate is oxidizing. The panel isn’t structurally done yet, but it will be in another two to three Austin summers.

Replacement Cost & What’s Included

For Boral shingle repair in Austin, plan on $225 – $475 for a single-tile or single-panel replacement on a walkable roof, with the low end covering concrete tile and the high end covering stone-coated steel with interlock disassembly. Steep pitches above 7/12, two-story work, or multiple damaged sections push that to $500 – $900. Here’s what’s included in our written price, every time: the replacement tile or panel, matching fasteners and clips, removal and disposal of the damaged piece, sealing and underlayment repair if the old underlayment was compromised, and a written warranty on the repair. We price the part and the labor separately on your quote so you can see exactly what the material costs versus the work. If we find decking rot once we open the area, we’ll show you before we proceed. No surprises, no change orders that you didn’t approve.

DIY or Call Us?

Some of this you can assess yourself, safely, from the ground or a ladder: count the damaged tiles, photograph the damage, check your gutters for granules, and look for water stains inside the attic. What you should not do is walk a Boral roof without proper shoes and fall protection; these products are heavy and durable, but the surface is slippery when dusty or damp, and a two-story fall isn’t worth a $300 repair savings. The other reason to call us: matching the existing tile. Boral’s color batches vary by year, and installing a slightly-off replacement panel will stand out for the lifetime of the roof. We have a decent library of Austin installations we can reference, and Greg Holloway reads a roof the way other people read a weather report: quickly, accurately, and without any drama. If you’re unsure whether it’s a one-tile fix or something bigger, call (254) 540-7345 and we’ll talk you through what you’re seeing before we ever put a ladder on the house.

FAQs